Archive for Blogs

Prep Once, Eat for a Week: 10 Meals for $50

Reposting from Exos:
Amanda Carlson-Phillips
May 18, 2009

Pingu196 / flickr

No time to prepare fresh meals every night? That doesn’t mean you’re confined to order in junk. You just need some planning, and we’ve done the leg work for you. What follows is a how-to guide for preparing all your meals on the weekend and eating for an entire week. You’ll save money by brown-bagging it to work and you can quickly assemble the muscle-building, energy-boosting dinners at home in minutes. The best part: We priced it out on a budget, so you’ll get a week’s worth of lunches and dinners for $50.

  Lunch Dinner
Sun Tilapia with Brown Rice + Spinach Salad
Mon Lean Deli Meat Wrap, Carrots, Hummus + Fruit Grilled Flank Steak with Potato Squares + Salad
Tues Chicken Salad Fish Tacos 
Wed Flank Steak Wrap + Berries Chicken Pasta Marinara + Salad 
Thurs Leftover Pasta Low-Fat Chicken Caesar Salad
Fri Flatbread Chicken Sandwich +Fruit 

Sunday Preparation


  • Flank Steak: Rub flank steak with 1 tbsp of olive oil, salt and pepper and 1 tbsp of Worcestershire sauce . Grill or cook the steak to your liking.
  • Chicken: Rub chicken with salt a pepper, coat the chicken breast with 3 tbsp of honey mustard dressing and grill or cook in a pan until juice runs clear.
  • Fish: Sprinkle 3 oz of fish with blackened seasoning. If you’re cooking salmon, then preheat the oven to 350 degrees. While it’s preheating, melt 1/2 tbsp of butter and a 1/4 cup of lemon juice in a saucepan. Drizzle the mixture over the fish, sprinkle with dill weed and bake for 15 minutes. If you’re cooking white fish, then preheat the over to 425 degrees. While it’s preheating, combine a 1/2 tbsp of lime juice, 1/8 tsp of onion powder and 1/8 tsp of black pepper in a bowl and drizzle over the fish. Top fish with olive oil, bake for 20 minutes and sprinkle with parsley.


  • Wash, cut and store green and red peppers, onions and red cabbage.
  • Saute four peppers and half an onion in 1 tbsp of olive oil.


  • Rice: Cook rice according to package directions.
  • Pasta: Cook pasta according to package directions.
  • Sweet Potatoes: Cut sweet potatoes into 1-inch squares, coat them with olive oil, salt, pepper, dried oregano and basil and bake at 450 degrees for 30 minutes.

The Grocery List


  • 1 1/2 lbs flank steak
  • 6 oz chicken
  • 6 oz of fish
  • 6 oz lean deli meat


  • Corn tortillas
  • Sweet potatoes
  • 100% Whole Wheat or Flour Tortillas


  • 1 baby carrots
  • 1 red and 1 green bell peppers
  • 1 bag of greens (spinach, romaine or kale)
  • 1 avocado
  • 1 tomato (Roma or grape)
  • 1 red onion and 1 sweet onion
  • 1 green onion (scallion)
  • 1 bunch garlic
  • 1 red cabbage
  • Cilantro and parsley
  • 1 lemon and 1 lime
  • 1 apple
  • 1 pear
  • 2 containers of berries
  • 1 mango
  • 1 orange, 1 tangerine, 1grapefruit

The Grocery Staples

  • Natural peanut butter
  • Reduced-fat mayonnaise
  • Dijon mustard
  • Low-sodium soy sauce
  • Salsa
  • Extra-virgin olive oil
  • Balsamic vinegar
  • Parmesan cheese
  • Honey
  • Tabasco sauce
  • Dried spices—garlic, thyme, rosemary, basil, lemon, salt and pepper
  • Chicken stock
  • Brown rice
  • Whole wheat pasta
  • Marinara sauce
  • Pickles
  • Canned black beans
  • Worcestershire sauce
  • Hummus
  • Low-fat dressing
  • Blackened seasoning

Maschine Mikro Tutorial 3 of 3

Maschine Mikro Tutorial 2 of 3

Maschine Mikro Tutorial 1 of 3

Healthy Grocery List

I don’t know about you, but I used to dred going to the grocery store to buy stuff for meals.  It is very time consuming, you need to pay close attention to what you are picking out, and you need to try and remember everything you need to restock your refrigerator and cabinets.  Additionally, it is hard to try and choose the most healthy combination of foods while you have gummi bears and potato chips staring you down.

A method that is commonly used by people who maintain a pretty specific diet plan is to keep a grocery list of the most common foods they eat for each meal.  Sure, this sounds basic, but I have found that one of the most effective tricks to keeping me eating healthy foods, and staying on track for my dietary needs has been to create a grocery list that is associated with meals that I eat reguarly and to purchase only the specific items on my list when I am out shopping at the grocery store.

A site I have found that has been extremely helpful for me to coordinate both my grocery list and meals is called  It is a really easy site to use, and it makes creating a grocery list a no-brainer.

Using the site is easy.  Visit the site, select a category of recipes you would like to see, and then browse through the food recipes you would like to put together for your meals.  Once you have selected a few recipes, you will then be able to generate a grocery list of all the recipe items you have selected.  It is that simple.  The grocery list outputs to a very clean, well-organized punch list.  The categories for recipes is very inclusive of many diet types, and I was also impressed with the extremely large selection of available recipes to choose from.  Selecting meals and picking your groceries based on those meals has not been easier!


How to make a light duty solar panel junction box

If you have multiple solar panels and you want to connect them together to form an array, it is very helpful to create a solar panel junction box to help keep the wiring organized, and to also help eliminate reductions in voltage or watts coming from the solar panels.  In this write up, I will describe how to make a light duty solar panel junction box.  My definition of a light duty solar panel junction box is a box intended to be used to join low voltage, low amperage, low wattage solar panels together in parallel.  If you have 12 volt solar panels under 5 amps, that use 18-12 guage wiring – then this box will work for you.  If you have higher wattage solar panels that use MC4 connections, I recommend you view my write up for a heavy duty solar panel junction box.

When I created this light duty solar panel junction box, my intention was to create a solar panel array that was composed of 6 15 watt solar panels all wired in parallel.  This way the amperage and voltage would stay the same, but we would be increasing the joined wattage of the panels at the junction box.  I had started with two of the harbor freight 45 watt solar panel kits that use 12 guage wire and do not produce a lot of juice compared to larger panels.  I planned to install these panels on the roof of my garage, run the wiring to the junction box, and then run the junction box to a charge controller that would regulate my battery bank.  I wanted to keep the setup as simple and clean as possible.  The junction box you are creating is basically just an enclosed positive and negative bus bar that joins all of the positive leads of the solar panels to one bar, and all of the negative leads of the solar panels to the other bar.  Again, this is parallel wiring, so the amperage does not increase, the voltage does not increase, but the wattage does increase.

Step 1:

Go to Radio Shack and pick up the following items:

1) Project Box Enclosure

2) Barrier Strip – 8 or 12 position

3) Jumper Strip (if they do not have anymore, get a pronged electrical connector that can be used as a jumper

4) Grommets

5) 12 guage wire with two leads.  If they only have 1 lead, then get two reels – 1 red and 1 black

6) Super Glue

Step 2:

Take out the Barrier Strips and Jumpers and connect the jumpers to the barrier strip:

Step 2 option B if no jumpers are available:

Step 3:

Super Glue the new barrier strip with junctions inside the project box:

Step 4:

Drill a holes in the bottom of your project box large enough for two wire lead in the bottom of the junction box, and drill one giant hole (largest grommet size) in the top of your box for all of the leads from the solar panels, and install your grommets.  Connect one of your wires leads to one strip, and one wire to the other barrier strip.

Step 5:  Run all of the leads from your solar panels into the large top holes on your junction box.

Step 6: Connect all of the positive wires from your solar panel to one barrier strip.  Then connect all of your negative wires from the solar panel to the other barrier strip.
You will now have one positive bus bar, and one negative bus bar.  Your junction box just helped you to take all of those messy wires from the solar panel, and organize the
into one neat box that not only combines all of the panels together in parallel, but also now gives you two nice neat wires to work with.

Step 7: Connect the new single positive lead to your charge controller, and then connect the new single negative lead to your charge controller.

Step 8: Connect your charge controller to your battery.


Here is a great device to use for measuring the wattage output of your solar panels back into your grid.  It is called the Kill-A-Watt from P3.  This device is usually used to help you determine what appliances in your house are using the most wattage, and to help you get control of your electricity waste in your home.  We have included the original description below so that you can see how useful this tool is – but here is how we use it for our solar panel grid-tie setup.

We use this device in line with our solar panels and our grid tie inverters to measure how many watts, and amps our solar panels are actually producing through our grid tie inverter, and how much energy we are putting back into our grid.  This device is great because it plugs into your outlet, and they you plug your grid tie inverter into it.  Once you switch on the inverter, the Kill-A-Watt, starts recording how many amps, and watts are being produced.  It will even show you how many Kw have been created and over how many hours so that you can really judge the effectiveness of your panels.  We think it is a great device and we have it hooked up to all of our solar panel arrays that are grid-tied.
HERE IS WHAT THE KILL-A-WATT is normally used for:
The Kill-A-Watt allows you to connect your appliances and assess how efficient they are. A large LCD display counts consumption by the Kilowatt-hour.  You can figure out your electrical expenses by the hour, day, week, month, even an entire year. Monitor the quality of your power by displaying Voltage, Line Frequency, and Power Factor.

  • Enables cost forecasting
  • Accurate to within 0.2%
  • Cumulative killowatt-hour monitor
  • Displays Volts, Amps, Watts, Hz, VA, KWH, Power Factor
  • Operating voltage: 115 VAC
  • Max current: 15 A
  • Max power: 1875 VA

You can find these online, ebay, or even radio shack.

Grid Tie Solar Inverter

What is a Plug and Play Solar Grid Tie Inverter?

A Grid Tie inverter is a simple device that takes direct solar panel electrical input, and then steps it up to a pure syne wave that can be pumped into your household grid through a recepticle.  These devices look like AC/DC inverters, and in a way they are, but they are pure syne wave inverters that output AC electricity.  So they take the power from your solar panels, and then pump them into your house grid – allowing you to input the juice you are creating to your own home electrical grid.

There are pros and cons to using these, and in our experience, here are a few things to be aware of when using these devices.
1) When these devices are on, you DO NOT want to unplug them, as you can get an electrical shock.  Since these actually push electrical out of the male plug back into your house recepticle, these work opposite of what you are used to with normal plugs, and you should never touch the male plug from the Grid Tie Inverter while it is on, as it will electrocute you.

2) These should only plugged into a dedicated GFI circuit coming directly out of your main breaker box.  You really should have a shut-off switch between your main breaker and the GFI this is plugged into to completely eliminate this device from the grid in the event of a grid shut-down.  These devices have a safety on them that shuts them down when no grid electricity is detected, but if you have this plugged into the grid, producting electricity during a black-out, there is a possibility that a line-man could get a zap from your device.

3) We have learned that regardless of what the actual watts of power these inverters claim to produce, they are really only half effecient, and you should never try to overload them with more than half their capacity or they will overheat or catch on fire.  So if you have a 600watt Grid tie inverter – expect to only run 300 watts of solar panel juice to it, and expect it only to produce about 300 watts.  This is very important to note, as these have a tendancy to over-heat and shut-down or catch on fire if you overload them.

4) You can stack these devices to try and get more power output from them, but we do not recommend this.  It is best to keep them running separately on their own circuits when using more than one on your grid.  What happens with these units is when they are stacked, they actually become master and slave units, and the slave unit hardly gets any say in the amount of power or output it produces.  The master likes to take over, and they you are overloading that device.  So keep them on separate circuits, and pnly feed them from separate solar panel arrays.


Installing a Grid Tie Inverter is very simple.  Just connect the Red leads from the solar panels to the Red DC Input pole on the inverter, and connect the Black leads from the solar panels to the Black DC Input pole on the inverter.  Connect a ground wire to the ground lead and connect this to a ground terminal on your house.  Then plug the male AC Output plug connection into a dedicated GFI outlet on your house.  ONCE THIS IS PLUGGED IN, DO NOT EVER DISCONNECT IT WHILE THE UNIT IS ON!  Then turn on the inverter.  It will indicate that it is generating power to the grid by the LED lights on the side.  We recommend that you plug in a Kill-a-watt meter between your GFI and inverter to measure how much juice it is pushing back into the grid.

Peter Tkacz’s Photography

Check out my buddy Peter Tkacz’s photography.  He shoots some really cool old school film photography.

Healthy and balanced blueberry breads menu

Healthy blueberry breads food

Everyone reading this article article can have had wholesome banana bread recipe. The taste with the healthy produced you right here. Let me tell you to remain reading this to locate what you came up for. There are plenty of healthy banana bread recipe tried through men and women at your house. Everyone loves the flavor of the loaves of bread especially kids. It is a healthy food parents might make for their children and ensure they will get the essential levels of vitamins and minerals from the bakery. The banana bread recipe is rich in carbohydrates.

There are many approaches to make the banana bread recipe, that you simply must have regarded or at least heard in your sooner day. The various styles of generating the breads only helps to make the bread additional tasty healthy and balanced. Healthy banana bread recipe would be the mother’s friends because it helps them in order to serve their children a very delicious and wholesome snack always. For a solo reason that children like the special banana bread, they would try to eat as much as you give them. I understand that every mom who makes the healthy strawberry bread for their children could try incorporating extra components to the mix to change the flavors a bit. This is a good idea since your children wouldn’t normally have to take bread concentrating on the same taste daily that might get them bored. And so, let us visit a simple nutritious banana bread recipe.

This is usually a special banana bread food. This is likely to be a great practical experience sharing the best banana loaf of bread recipe which i had in existence. A special recipe you would want to bake and also eat. A recipe consists of nine materials. So, we have found our several steps healthy banana bread recipe.
. Almost all purpose flour ( space ) 1 tumbler
. Whole wheat flour ( blank ) 1 mug
. Brown sugar or honies – ? goblet
. Baking soda pop and Preparing your receipee powder- 1 Tablespoon each
. Ovum – Just one
. Salt and also Cinnamon * ? – pertaining to flavor
. Crushed bananas * 1 ? mug
This is the easiest method to make the very best healthy banana bread recipe. A 1 ? cup of mashed banana could be equal to 5-6 bananas. Allow us to see the guidelines to make a dough in order to bake.
. The First step is to overcome the egg cell and then conquer it while using the mashed banana bread recipe. Now combine the hitter with the different ingredients that we certainly have ready, sugar/honey or even a mix of the two, salt and also cinnamon.
. The second step should be to mix flour, wheat flour, baking powder and soft drink. Once they tend to be mixed fill in the blend made in step one. If needed, it’s fine to use nuts with it.
. The third phase is to blend the mixture for a while in addition to pour this a loaf of bread pan. Bake the crepe mixture in One hundred eighty C or 350 Farreneheit for 1 out of 3 minutes.
After 50 a matter of minutes stick a knife for the bread and also confirm to control your emotions. Now you can trim the lf in to the shapes your children need and function them.

You are able to always obtain numerous facts concerning banana bread recipe at our site dedicated to Banana Recipes.